While some keyboardists claim to hear a 5ms discrepancy in their performances, the vast majority of musicians are unlikely to worry about 10ms, and many should find a latency of 23ms or more perfectly acceptable with most sounds, especially pads with longer attacks.
Table of Contents
What is a good latency for recording?
While some keyboardists claim to hear a 5ms discrepancy in their performances, the vast majority of musicians are unlikely to worry about 10ms, and many should find a latency of 23ms or more perfectly acceptable with most sounds, especially pads with longer attacks.
Does latency matter for recording?
You will often hear salesmen or so called experts recommending this gear over that gear because you will get better latency. The truth of the matter is latency does not matter at all for the recording needs of nearly every home recording enthusiast. Most of you literally should not care about latency at all.
What is latency in sound recording?
Latency refers to a short period of delay (usually measured in milliseconds) between when an audio signal enters a system and when it emerges.
What causes latency recording?
While each step in the process only takes milliseconds, there are a variety of factors that can increase the amount of time each step takes, thus increasing the amount of latency. The most common reasons why latency occurs are the audio driver(s) and hardware you’re using, and also the buffer size and sample rate.
How much latency is OK?
Latency is measured in milliseconds, and indicates the quality of your connection within your network. Anything at 100ms or less is considered acceptable for gaming. However, 20-40ms is optimal.
Is 10ms latency noticeable?
10 ms might be just barely noticeable. On a typical laptop with a refresh rate of 60 Hz, each frame is on the screen for about 16-17 ms, so (all else being equal) a 10 ms delay means a roughly 66% chance of making the image show up one frame later.
What is the best buffer size for recording?
A good buffer size for recording is 128 samples, but you can also get away with raising the buffer size up to 256 samples without being able to detect much latency in the signal. You can also decrease the buffer size below 128, but then some plugins and effects may not run in real time.
How can I record without latency?
How to reduce audio interface latency
- Reduce the buffer size. The smaller the buffer size, the lower the latency.
- Raise the sample rate.
- Disable the Audio Input Device.
- Use ASIO audio drivers on Windows.
- Use a dedicated audio interface running native drivers.
- Don’t use Bluetooth devices or cast audio.
Is 5ms latency good audio?
While we can’t generally hear the effects of latency until they are around 15-30 milliseconds (ms), performers can begin to feel them at around 5-10ms. At 7ms, latency starts to mess with our ability to play or sing on top of or behind the beat. Sound starts to feel sluggish at 10ms.
Is high or low latency better?
Aim for Low Latency Network latency is how long it takes for data to travel between its source and destination. The lower the latency, the better. If you’re gaming with high latency, you might tell your character to walk forward but they won’t actually move for a few seconds. This is what causes lag.
How can I improve my latency?
How do you fix high latency?
- Turn off any downloads, and be sure to check for anything that’s downloading in the background.
- Close any unused applications or browser tabs.
- Check for malware.
- Use an Ethernet cable to connect your device to your router or modem, if at all possible.
Is higher buffer size better for recording?
This means that when recording with a lower buffer size at a higher sample rate, the audio will be better quality, but the latency will be increased as it needs to process more data. Conversely, recording with a larger buffer size at a lower sample rate will result in lower latency but with reduced frequency bandwidth.
How do I lower my recording latency?
How to reduce latency
- Audio interface latency.
- Device/Plug-in related latency.
- Reduce the buffer size.
- Raise the sample rate.
- Disable the Audio Input Device.
- Use ASIO audio drivers on Windows.
- Use a dedicated audio interface running native drivers.
- Don’t use Bluetooth devices or cast audio.
What is ideal latency?
What is an acceptable latency?
The difference between high and low latency Generally, an acceptable latency (or ping) is anywhere around 40 – 60 milliseconds (ms) or lower, while a speed of over 100ms will usually mean a noticeable lag in gaming.
Can you have zero latency?
As such, a zero ping is the perfect scenario. This means that our computer was communicating instantly with a remote server. Unfortunately, due to the laws of physics, data packets take time to travel. Even if your packet travels entirely over fiber-optic cables, it cannot travel faster than the speed of light.
How much latency is too much?
What is good latency for gaming?
| Latency | Milliseconds |
|---|---|
| Bad | Greater than 100ms |
| Acceptable | 40-100ms |
| Good | 20-40ms |
| Great | Less than 20ms |