How do I reset my Cisco AP to factory settings?

Reset Cisco Wireless AP to factory defaults

How do I reset my Cisco AP to factory settings?

Reset Cisco Wireless AP to factory defaults

  1. Connect the console cable.
  2. Unplug the power or network cable if connected to a POE switch.
  3. Press and hold the Mode button.
  4. Plug the power back into the AP.
  5. Wait until the output on the console says button is pressed.

How do I reset my Cisco Air cap2602i a K9?

How to factory reset (hard reset) Cisco AIR-CAP2602E-A-K9 :

  1. When the router is on, press the button reset and hold for 30 seconds.
  2. While holding down the button reset, turn off the power of the router and hold down the button reset for 30 seconds.

How do you reset a Cisco switch with the mode button?

Hold the “mode” button on the front of the switch for 10 seconds. The lights will blink then go solid – the switch completely wipes all configuration and then reboots.

How do I reset my cisco Air AP1242AG a K9?

How to factory reset (hard reset) Cisco AIR-AP1242AG-A-K9 :

  1. When the router is on, press the button reset and hold for 30 seconds.
  2. While holding down the button reset, turn off the power of the router and hold down the button reset for 30 seconds.

How do I reset my cisco Air ap1142n a K9?

To reset the AP, try these steps: Step 1 Disconnect power from access point. Step 2 Press and hold MODE button while you reconnect power to the access point. Step 3 Hold the MODE button until the status LED turns amber, and release the button.

Where is the reset button on Cisco Router?

The default username is cisco and the default password is cisco. Step 1. Press the Reset button located at the back of the device with a pin for approximately 15 seconds or until the power light on the front of the device starts flashing. The Router reloads and is set to the default configuration settings.

How do you reset a cisco switch physically?

Step 1. Disconnect all Ethernet cables from the switch. Step 2. Using a pin, press and hold the Reset button on the switch for 15 to 20 seconds.

How do I wipe my router clean?

How to reset your router to restore factory default settings

  1. Locate the Reset button on the back of your router.
  2. With the router powered on, use the pointed end of a paperclip or similar object to press and hold the Reset button for 15 seconds.
  3. Wait for the router to fully reset and power back on.

How do I wipe my cisco router?

Follow these steps:

  1. Log on. to your router, and enter the privileged EXEC mode by entering enable and then entering the enable password command.
  2. Enter configure terminal to go to Global.
  3. Enter config-register 0x2102.
  4. Enter end, and then enter the write erase command to delete the.
  5. Enter reload to reload the router.

How do I Reset my cisco router to factory default?

Reset Router to Default Configuration

  1. With the router powered off, connect the power cord to your router, and plug the power cord into your power source.
  2. Find the Reset button on the router.
  3. Press and hold the Reset button while you power on the router.
  4. Release the Reset button after 10 seconds.

Is there a way to hard reset a switch?

How to Perform a Hard Reset (Factory Reset) on a Nintendo Switch

  1. With the system powered down, hold the power button until the console resets. This step can take up to 15 seconds.
  2. Release the power button, then press it once to start the console like normal.
  3. Your console should boot up without any issue.

How do I factory reset my switch without Internet?

Complete These Steps:

  1. Ensure the console is powered off.
  2. With the console powered off, press and hold down the volume up (+) and volume down (-) buttons, then press the POWER Button to turn the console on.
  3. Once in recovery mode, select “Restore Factory Settings Without Deleting Save Data”.

How do I Reset my Cisco AP to factory settings?

Reset Cisco Wireless AP to factory defaults

How do I Reset my Cisco AP to factory settings?

Reset Cisco Wireless AP to factory defaults

  1. Connect the console cable.
  2. Unplug the power or network cable if connected to a POE switch.
  3. Press and hold the Mode button.
  4. Plug the power back into the AP.
  5. Wait until the output on the console says button is pressed.

How do I Reset my Cisco 1142 to factory settings?

Step 1 Disconnect power from access point. Step 2 Press and hold MODE button while you reconnect power to the access point. Step 3 Hold the MODE button until the status LED turns amber, and release the button.

How do I manually Reset a Cisco switch?

Manually Reset the Switch Step 1. Disconnect all Ethernet cables from the switch. Step 2. Using a pin, press and hold the Reset button on the switch for 15 to 20 seconds.

How do I Reset my Cisco wireless router?

The default username is cisco and the default password is cisco. Step 1. Press the Reset button located at the back of the device with a pin for approximately 15 seconds or until the power light on the front of the device starts flashing. The Router reloads and is set to the default configuration settings.

What is the default username and password for cisco AP?

The default username is Cisco. Step 4 Enter the wireless device password in the Password field and press Enter. The default password is Cisco.

Can you reset an access point?

Resetting the access point using the Reset button Press and hold the Reset button of your access point for 30 seconds. Once the access point is reset, perform a powercycle. Unplug the access point’s power cable and wait for 30 seconds then plug it back in. Wait for the access point’s lights to appear solid.

How do I reset my Cisco WAP4410N to factory settings?

How to factory reset (hard reset) Cisco WAP4410N :

  1. When the router is on, press the button reset and hold for 30 seconds.
  2. While holding down the button reset, turn off the power of the router and hold down the button reset for 30 seconds.

How do I reset my Cisco Aironet 1142?

Hi, Step 1 Disconnect power from access point. Step 2 Press and hold MODE button while you reconnect power to the access point. Step 3 Hold the MODE button until the status LED turns amber, and release the button.

How do I Reset a cisco switch to factory command line?

Resetting the Cisco IP switch to factory defaults

  1. Reset the switch to factory defaults: Erase the existing configuration: write erase. Reload the switch software: reload.
  2. Save the configuration: IP_switch-A-1# copy running-config startup-config.
  3. Reboot the switch and wait for the switch to reload: IP_switch-A-1# reload.

How do you Reset a switch?

How to Perform a Hard Reset (Factory Reset) on a Nintendo Switch

  1. With the system powered down, hold the power button until the console resets. This step can take up to 15 seconds.
  2. Release the power button, then press it once to start the console like normal.
  3. Your console should boot up without any issue.

How do I Reset my router to factory settings?

How to reset your router to restore factory default settings

  1. Locate the Reset button on the back of your router.
  2. With the router powered on, use the pointed end of a paperclip or similar object to press and hold the Reset button for 15 seconds.
  3. Wait for the router to fully reset and power back on.

How do I reset my cisco router to factory settings without a password?

Reset Router Using Reset Button

  1. With the router powered off, connect the power cord to your router, and plug the power cord into your power source.
  2. Find the Reset button on the router.
  3. Press and hold the Reset button while you power on the router.
  4. Release the Reset button after 10 seconds.

How do I reset my cisco access point password?

1. Press and hold the MODE button while you reconnect power to the AP. 2. Hold the MODE button until the Status LED turns amber (approximately one to two seconds), and release the button.

How do I reset my Cisco access point password?

What is the default IP for Cisco WAP4410N?

IP Address 192.168.1.245 Load Admin
Username admin
Password admin
SSID ciscosb
Users Manual User manual 2 of 2

How do I access Cisco WAP4410N?

Type 192.168. 1.245 (the default IP to access the admin interface) in the address bar of your internet browser to access the router’s web-based user interface. You should see 2 text fields where you can enter a username and a password. The default username for your Cisco WAP4410N is admin.

How do I reset my Cisco Aironet 1100?

1 Answer

  1. Step 1 Disconnect power from access point.
  2. Step 2 Press and hold MODE button while you reconnect power to the access point.
  3. Step 3 Hold the MODE button until the status LED turns amber, and release the button.