Nail plates are flat strips of galvanised steel which have been punched to create multiple small prongs on one side. These are hammered into the surface of adjacent pieces of timber to hold them together. They are widely used in framed structures and in the prefabrication of structural elements such as trusses.
Table of Contents
How thick does a nail plate need to be?
0.0478 inches
312.9 Steel Nail Plates Plastic and copper or copper alloy piping penetrating framing members to within 1 inch (25.4 mm) of the exposed framing shall be protected by steel nail plates not less than No. 18 gauge (0.0478 inches) (1.2 mm) in thickness.
What are nail plates used for?
Nail plates are flat strips of galvanised steel which have been punched to create multiple small prongs on one side. These are hammered into the surface of adjacent pieces of timber to hold them together. They are widely used in framed structures and in the prefabrication of structural elements such as trusses.
What are nail plates called?
The nail plate (corpus unguis) sometimes referred to as the nail body, is the visible hard nail area from the nail root to the free edge, made of translucent keratin protein. Several layers of dead, compacted cells cause the nail to be strong but flexible.
Are nail plates required for electrical?
It only applies to cables passing through a hole in the member. It sounds like in your case, the cables are run on top of the purlins, so technically, you do not need nail plates there.
Where do you put nail plates?
To add a measure of safety, nail plates should be installed on both sides of the wall stud to protect both sides of the wiring. This is most easily done during the construction phase (new, addition, or remodel) of the building process.
When should nail plates be used?
A nail protection plate helps prevent nails from piercing pipes and electrical lines after the plaster walls are installed and the finish trim is being applied. Nail Protection Plates are typically installed over utilities that pass through framing members. the most common are 1/2 in.
Where do I need to install nail plates?
What is underneath the nail plate?
Underneath the nail plate is the nail bed. The nail bed is where the nail adheres to the finger. Other key elements of the nail include: Lunula.
How do you install a nail plate?
How to Install Nail Plates to Protect Electrical Wiring
- Drill wiring holes through the wall studs.
- Hold a nail plate in place on the drywall side of the wall stud, over the wiring hole.
- Repeat on the other side of the stud in the same location.
Where steel nail plates are required what is the minimum thickness allowed?
Where this distance cannot be maintained, the cable or raceway shall be protected from penetration by nails or screws by a steel plate, sleeve, or equivalent at least 1/16 in. (1.59 mm) thick.
Does the nail plate grow back?
After a nail separates from the nail bed for whatever reason, it will not reattach. A new nail will have to grow back in its place. Nails grow back slowly. It takes about 6 months for a fingernail and up to 18 months for a toenail to grow back.
How do you grow a nail plate?
How to make your nail beds appear longer
- Grow out your nails. First step is to let your nails grow out.
- Use a nail brush for cleaning instead of a nail scraper. You can also make your nail beds appear longer by cleaning underneath your nails with a nail brush instead of metal nail tools.
- Push back your cuticles.
Do nail plates affect drywall?
Yes, nail plates can cause a bulge in the drywall.
Why is it important to use nailing plates when water pipes are too close to the edge of a framing member?
Without proper protection from nail protectors, it’s not that uncommon to drive a nail right through to a live wire or water pipe. Nail plates, especially when installed on both sides of each wall stud, can eliminate accidental electrical shock, leaky pipes leading to extreme water damage, and fire risk.
How do I protect my nail bed after losing my nail?
Keep the nail bed dry, clean, and covered with petroleum jelly and an adhesive bandage until the nail bed is firm or the nail has grown back. Apply a new adhesive bandage whenever the bandage gets wet. Watch for signs of infection such as increasing heat, redness, pain, tenderness, swelling, or pus.
Do nail plates grow back?
In most cases, the nail will grow back from the area under the cuticle (the matrix). A fingernail takes about 4 to 6 months to grow back. A toenail takes about 12 months to grow back. If the nail bed or matrix was damaged, the nail may grow back with a rough or abnormal shape.